first commit
This commit is contained in:
Sophie Schiller
commit
be8e71507b
8 changed files with 329 additions and 0 deletions
193
src/main.ino
Normal file
193
src/main.ino
Normal file
|
|
@ -0,0 +1,193 @@
|
|||
/*
|
||||
Arduino and MPU6050 Accelerometer and Gyroscope Sensor Tutorial
|
||||
by Dejan, https://howtomechatronics.com
|
||||
*/
|
||||
|
||||
#include <Wire.h>
|
||||
#include <FastLED.h>
|
||||
|
||||
#define LED_PIN 7
|
||||
#define NUM_LEDS 20
|
||||
|
||||
const int MPU = 0x68; // MPU6050 I2C address
|
||||
float AccX, AccY, AccZ;
|
||||
float GyroX, GyroY, GyroZ;
|
||||
float accAngleX, accAngleY, accCombined, gyroAngleX, gyroAngleY, gyroAngleZ;
|
||||
float roll, pitch, yaw;
|
||||
float AccErrorX, AccErrorY, GyroErrorX, GyroErrorY, GyroErrorZ;
|
||||
float elapsedTime, currentTime, previousTime;
|
||||
int c = 0;
|
||||
boolean debug = true;
|
||||
|
||||
CRGB leds[NUM_LEDS];
|
||||
|
||||
void setup() {
|
||||
Serial.begin(19200);
|
||||
//setup LEDs
|
||||
FastLED.addLeds<WS2812, LED_PIN, GRB>(leds, NUM_LEDS);
|
||||
|
||||
//setup IMU
|
||||
Wire.begin(); // Initialize comunication
|
||||
Wire.beginTransmission(MPU); // Start communication with MPU6050 // MPU=0x68
|
||||
Wire.write(0x6B); // Talk to the register 6B
|
||||
Wire.write(0x00); // Make reset - place a 0 into the 6B register
|
||||
Wire.endTransmission(true); //end the transmission
|
||||
|
||||
// Configure Accelerometer Sensitivity - Full Scale Range (default +/- 2g)
|
||||
/*Wire.beginTransmission(MPU);
|
||||
Wire.write(0x1C); //Talk to the ACCEL_CONFIG register (1C hex)
|
||||
Wire.write(0x10); //Set the register bits as 00010000 (+/- 8g full scale range)
|
||||
Wire.endTransmission(true);
|
||||
// Configure Gyro Sensitivity - Full Scale Range (default +/- 250deg/s)
|
||||
Wire.beginTransmission(MPU);
|
||||
Wire.write(0x1B); // Talk to the GYRO_CONFIG register (1B hex)
|
||||
Wire.write(0x10); // Set the register bits as 00010000 (1000deg/s full scale)
|
||||
Wire.endTransmission(true);
|
||||
*/
|
||||
delay(20);
|
||||
|
||||
// Call this function if you need to get the IMU error values for your module
|
||||
//calculate_IMU_error();
|
||||
delay(200);
|
||||
|
||||
}
|
||||
|
||||
void calculateOrientationData() {
|
||||
// === Read acceleromter data === //
|
||||
Wire.beginTransmission(MPU);
|
||||
Wire.write(0x3B); // Start with register 0x3B (ACCEL_XOUT_H)
|
||||
Wire.endTransmission(false);
|
||||
Wire.requestFrom(MPU, 6, true); // Read 6 registers total, each axis value is stored in 2 registers
|
||||
//For a range of +-2g, we need to divide the raw values by 16384, according to the datasheet
|
||||
AccX = (Wire.read() << 8 | Wire.read()) / 16384.0; // X-axis value
|
||||
AccY = (Wire.read() << 8 | Wire.read()) / 16384.0; // Y-axis value
|
||||
AccZ = (Wire.read() << 8 | Wire.read()) / 16384.0; // Z-axis value
|
||||
// Calculating Roll and Pitch from the accelerometer data
|
||||
accAngleX = (atan(AccY / sqrt(pow(AccX, 2) + pow(AccZ, 2))) * 180 / PI) - 0.50; // AccErrorX ~(0.58) See the calculate_IMU_error()custom function for more details
|
||||
accAngleY = (atan(-1 * AccX / sqrt(pow(AccY, 2) + pow(AccZ, 2))) * 180 / PI) + 1.98; // AccErrorY ~(-1.58)
|
||||
|
||||
accCombined = sqrt(pow(AccX, 2) + pow(AccY, 2) + pow(AccZ, 2));
|
||||
|
||||
// === Read gyroscope data === //
|
||||
previousTime = currentTime; // Previous time is stored before the actual time read
|
||||
currentTime = millis(); // Current time actual time read
|
||||
elapsedTime = (currentTime - previousTime) / 1000; // Divide by 1000 to get seconds
|
||||
Wire.beginTransmission(MPU);
|
||||
Wire.write(0x43); // Gyro data first register address 0x43
|
||||
Wire.endTransmission(false);
|
||||
Wire.requestFrom(MPU, 6, true); // Read 4 registers total, each axis value is stored in 2 registers
|
||||
GyroX = (Wire.read() << 8 | Wire.read()) / 131.0; // For a 250deg/s range we have to divide first the raw value by 131.0, according to the datasheet
|
||||
GyroY = (Wire.read() << 8 | Wire.read()) / 131.0;
|
||||
GyroZ = (Wire.read() << 8 | Wire.read()) / 131.0;
|
||||
// Correct the outputs with the calculated error values
|
||||
GyroX = GyroX + 1.42; // GyroErrorX ~(-0.56)
|
||||
GyroY = GyroY - 0.51; // GyroErrorY ~(2)
|
||||
GyroZ = GyroZ + 1.00; // GyroErrorZ ~ (-0.8)
|
||||
|
||||
// Currently the raw values are in degrees per seconds, deg/s, so we need to multiply by sendonds (s) to get the angle in degrees
|
||||
gyroAngleX = gyroAngleX + GyroX * elapsedTime; // deg/s * s = deg
|
||||
gyroAngleY = gyroAngleY + GyroY * elapsedTime;
|
||||
yaw = yaw + GyroZ * elapsedTime;
|
||||
|
||||
// Complementary filter - combine acceleromter and gyro angle values
|
||||
roll = 0.96 * gyroAngleX + 0.04 * accAngleX;
|
||||
pitch = 0.96 * gyroAngleY + 0.04 * accAngleY;
|
||||
|
||||
// Print the values on the serial monitor
|
||||
if (debug) {
|
||||
Serial.print("Acceleration: ");
|
||||
Serial.print(accCombined, 3);
|
||||
Serial.print("\t");
|
||||
Serial.print("Orientation: ");
|
||||
Serial.print("\t");
|
||||
Serial.print(roll);
|
||||
Serial.print("\t");
|
||||
Serial.print(pitch);
|
||||
Serial.print("\t");
|
||||
Serial.println(yaw);
|
||||
}
|
||||
}
|
||||
|
||||
void enableLEDsOnAcceleration(){
|
||||
int ledcutoff = int(accCombined * NUM_LEDS / 2);
|
||||
if(debug) {
|
||||
Serial.print("[");
|
||||
}
|
||||
for (int i = 0; i <= ledcutoff; i++) {
|
||||
leds[i] = CRGB(64, 0, 0);
|
||||
if (debug) {
|
||||
Serial.print("|");
|
||||
}
|
||||
}
|
||||
for (int i = ledcutoff; i <= NUM_LEDS ; i++) {
|
||||
leds[i] = CRGB(0, 64, 0);
|
||||
if (debug) {
|
||||
Serial.print("-");
|
||||
}
|
||||
}
|
||||
if(debug) {
|
||||
Serial.println("]");
|
||||
}
|
||||
FastLED.show();
|
||||
}
|
||||
|
||||
void loop() {
|
||||
// === Read acceleromter data === //
|
||||
calculateOrientationData();
|
||||
enableLEDsOnAcceleration();
|
||||
delay(20);
|
||||
}
|
||||
|
||||
|
||||
void calculate_IMU_error() {
|
||||
// We can call this funtion in the setup section to calculate the accelerometer and gyro data error. From here we will get the error values used in the above equations printed on the Serial Monitor.
|
||||
// Note that we should place the IMU flat in order to get the proper values, so that we then can the correct values
|
||||
// Read accelerometer values 200 times
|
||||
while (c < 200) {
|
||||
Wire.beginTransmission(MPU);
|
||||
Wire.write(0x3B);
|
||||
Wire.endTransmission(false);
|
||||
Wire.requestFrom(MPU, 6, true);
|
||||
AccX = (Wire.read() << 8 | Wire.read()) / 16384.0 ;
|
||||
AccY = (Wire.read() << 8 | Wire.read()) / 16384.0 ;
|
||||
AccZ = (Wire.read() << 8 | Wire.read()) / 16384.0 ;
|
||||
// Sum all readings
|
||||
AccErrorX = AccErrorX + ((atan((AccY) / sqrt(pow((AccX), 2) + pow((AccZ), 2))) * 180 / PI));
|
||||
AccErrorY = AccErrorY + ((atan(-1 * (AccX) / sqrt(pow((AccY), 2) + pow((AccZ), 2))) * 180 / PI));
|
||||
c++;
|
||||
}
|
||||
//Divide the sum by 200 to get the error value
|
||||
AccErrorX = AccErrorX / 200;
|
||||
AccErrorY = AccErrorY / 200;
|
||||
c = 0;
|
||||
// Read gyro values 200 times
|
||||
while (c < 200) {
|
||||
Wire.beginTransmission(MPU);
|
||||
Wire.write(0x43);
|
||||
Wire.endTransmission(false);
|
||||
Wire.requestFrom(MPU, 6, true);
|
||||
GyroX = Wire.read() << 8 | Wire.read();
|
||||
GyroY = Wire.read() << 8 | Wire.read();
|
||||
GyroZ = Wire.read() << 8 | Wire.read();
|
||||
// Sum all readings
|
||||
GyroErrorX = GyroErrorX + (GyroX / 131.0);
|
||||
GyroErrorY = GyroErrorY + (GyroY / 131.0);
|
||||
GyroErrorZ = GyroErrorZ + (GyroZ / 131.0);
|
||||
c++;
|
||||
}
|
||||
//Divide the sum by 200 to get the error value
|
||||
GyroErrorX = GyroErrorX / 200;
|
||||
GyroErrorY = GyroErrorY / 200;
|
||||
GyroErrorZ = GyroErrorZ / 200;
|
||||
// Print the error values on the Serial Monitor
|
||||
Serial.print("AccErrorX: ");
|
||||
Serial.println(AccErrorX);
|
||||
Serial.print("AccErrorY: ");
|
||||
Serial.println(AccErrorY);
|
||||
Serial.print("GyroErrorX: ");
|
||||
Serial.println(GyroErrorX);
|
||||
Serial.print("GyroErrorY: ");
|
||||
Serial.println(GyroErrorY);
|
||||
Serial.print("GyroErrorZ: ");
|
||||
Serial.println(GyroErrorZ);
|
||||
}
|
||||
Loading…
Add table
Add a link
Reference in a new issue